Page 83 Inside of the unit, press the power supply release latch on the chassis base, and then lift up the rear of the power supply to disengage it from the chassis. This printer must first install the. Page 59 To create a bootable USB flash media device, you must have: Front Panel Components Drive configuration may vary by model. All other drives use M3 metric screws. Cause Solution The cables may not be connected properly.
|Date Added:||14 August 2009|
|File Size:||24.44 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Page 61 HP Pro System board connectors are color-coded to make it easier to find the proper connection. Bezel Blanks 1then discard the bezel blank. Serial Number Location Serial Number Location Each winndows has a unique serial number and product ID number that are located on the top cover of the computer. If you are removing a PCI or PCI Express x1 card, hold the card at each end and carefully rock it back and forth until hp pro 3500 microtower pc windows xp connectors pull free from the socket.
Information regarding recent vulnerabilities HP is aware of the recent vulnerabilities commonly referred to as “Spectre” and “Meltdown”. Power Cord Set Requirements The power supplies on some computers have external power switches. Two different chassis are available—microtower and small form factor.
Diskette drives are only available on some models.
Front Panel Components Drive configuration may vary by model. Figure Replacing the Thermal Sensor Slide the cover on hp pro 3500 microtower pc windows xp carrier 1 and replace the screw on the rear of the carrier to secure the cover in place 2.
System Fan Remove the four Phillips screws that secure the fan to the chassis, rotate the top of the fan forward, and then remove the fan from the chassis. HP Pro shown.
Power LED flashes Red six times, once every second, followed by a two second pause, and the computer beeps six times. Before replacing the battery, it is important to back up the computer CMOS settings.
Bezel Blanks Prepare the computer for disassembly Preparation for Disassembly on page Figure Removing the Hard Drive Cage Screws Push down the latch on the side of the hard drive cage 1then slide the hard drive cage away from the bottom of the chassis 2 as shown below.
Installing Memory Modules populated with the least amount of memory describes the total amount of memory assigned to dual channel and the remainder is assigned to single channel.
hp pro 3500 microtower pc windows xp If you are removing a standard PCI card or PCI Express x1 card, hold the card at each end, and carefully rock it back and forth until the connectors pull free from the socket. The computer will beep once after a POST text message is displayed on the screen. Host-based Plug and Play Basic driver These memory sockets are populated with at least one preinstalled DIMM. After Windows 10 release, the workaround is no longer tested for this printer.
The battery holder automatically secures the battery in the proper position. To install the security screw: To check, click the link in the Recommended solution column for the printer. Ensure that none of the keys are depressed. Miccrotower setup configuration is model-specific. Connector Pin Assignments This appendix contains the pin assignments for many computer and workstation connectors.
Page 94 Open both latches kicrotower the memory module socket 1hp pro 3500 microtower pc windows xp insert the memory module into the socket 2. Type 3 Battery Holder Plug in hp pro 3500 microtower pc windows xp computer and turn on power to the computer. Decoder wkndows is not installed. Contacting Customer Support Contacting Customer Support For help and service, contact an authorized reseller or dealer.
Figure Closing the Expansion Slot Retainer Connect external cables to the installed card, if needed.
You will see a brief movie followed by an online iwndows form. To reduce hp pro 3500 microtower pc windows xp of personal injury from hot surfaces, allow the internal system components to cool before touching.
Press the power button to resume from standby mode. Page The system will enter the operating system successfully. System Board Drive Connections System Board Drive Connections Refer to the following illustration and table to identify the system board drive connectors.
Connect external cables to the installed card, if needed.
Page Page Page – Installing pgo Hp pro 3500 microtower pc windows xp 5. Refer to the following illustration and table to identify the media card reader components. These settings have no effect under an ACPI-based operating system. Verify that the modem is connected and communicating properly. Batteries, battery packs, and accumulators should not be disposed of together with the general household waste.
Remove the four screws from the bottom of the hard drive carrier.