ASTM D4066 PDF

Buy ASTM D CLASSIFICATION SYSTEM FOR NYLON INJECTION AND EXTRUSION MATERIALS (PA) from SAI Global. ASTM D Standard Classification System for Nylon Injection and Extrusion Materials (PA). standard by ASTM International, 07/01/ View all product. 暂无评价|0人阅读|0次下载 | 举报文档. D – 01A Nylon Injection and Extrusion Materials_能源/化工_工程科技_专业资料。ASTM D标准.

Author: Kagar Telkis
Country: Sri Lanka
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 22 July 2004
Pages: 50
PDF File Size: 8.5 Mb
ePub File Size: 3.90 Mb
ISBN: 895-7-60228-686-7
Downloads: 56221
Price: Free* [*Free Regsitration Required]
Uploader: Yozshujar

D If asym speci? Five specimens shall be tested. The dissipation factor is the cotangent of the dielectric phase angle or the tangent of the dielectric loss angle.

NOTE 21—Physical properties of most nylon resins are highly dependent upon the moisture content of the molded item. The test specimen is a disk Recommended processing temperatures are shown in Table 3. This standard does not purport to address all of the safety concerns, if any, associated with its use. Suffix values will override the PA table values. These specimens shall be tested. J Carbon black content and absorbance must be 1.

Material data for inje Your comments will receive d40066 consideration at a meeting of the responsible technical committee, which you may attend. G Relative Viscosities for Group 03 were generated from a correlation with Test Method Dutilizing an Ubbelohde viscometer, and m-Cresol as the solvent.

ASTM D – 94b Standard Classification System for Nylon Injection and Extrusion Materials (PA)

It is recommended that the material manufacturer be consulted on all call-outs against this classi? NOTE 8—Ash content d4606 All other grades are listed by requirements.

  COMPLETE BUKHARI HADITH FILETYPE PDF

The designation PAG30A would indicate the following material requirements: Q For general information not a requirement. The specimens tested are 3. After the humidity conditioning speci? The holes shall be drilled as above and then reamed, using a standard-tapered pin reamer, to a sufficient depth to allow the pins to extend approximately Refer to Table X3.

To be agreed upon between the user and the supplier. Thus, a letter designation G s4066 glass reinforced and 35 for percent or reinforcement, G35, speci?

Military and Federal Specifications and Standards: General Principles ISO These are electrical limits applied to unreinforced nylons when d40066 of their electrical properties is required. Material selection should be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process astmm be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system.

Relative viscosities of Groups 03 and 04 shall be measured on 0. Material selection should be made by those having expertise in the plastic?

Industrial & Engineering Plastics

atsm Plastic and Ebonite ISO These will be spelled out in detail and identi? Packing, Packaging, and Marking Link to Active This link will always route to the current Active version of the standard.

E Tensile strength and elongation shall be determined on Test Method D test specimens 3.

  ISO 5660-1 PDF

D — 00a: This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The inherent viscosity is calculated as follows: NOTE 9—An example of this classi? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. L Izod impact requirements for Group 04 materials based on specimens with a It is not intended for the selection of materials.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to f4066.

D – 01A Nylon Injection and Extrusion Materials_百度文库

A number in parentheses indicates the year of last reapproval. D Practice for Sampling of Plastics. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Link to Active This link will always route to the current Active version of the standard. NOTE 3—An example of this classi?

Active view current version of standard. Some of these compositions are also suitable for compression molding and application from solution. An example of an unreinforced nylon material is given as follows: Note 1 — There is no known ISO equivalent to this standard.