EPCS4N DATASHEET PDF

EPCS4N Datasheet, EPCS4N PDF, EPCS4N Data sheet, EPCS4N manual, EPCS4N pdf, EPCS4N, datenblatt, Electronics EPCS4N, alldatasheet, free. EPCS4SI8 Intel / Altera FPGA – Configuration Memory IC – Ser. Config Mem Flash 4Mb 40 MHz datasheet, inventory, & pricing. EPCS4 Serial Configuration Devices Chapter 4. Serial Configuration Devices & EPCS64) Data Sheet. Features. The serial configuration devices provide the.

Author: Malazil Vudozil
Country: Guyana
Language: English (Spanish)
Genre: Health and Food
Published (Last): 15 January 2011
Pages: 82
PDF File Size: 8.57 Mb
ePub File Size: 8.23 Mb
ISBN: 695-9-21742-236-4
Downloads: 39110
Price: Free* [*Free Regsitration Required]
Uploader: JoJosida

The serial configuration devices provide the following features: Low cost, low pin count and non-volatile memory. Low current during configuration and near-zero standby mode. Available in 8-pin and pin small outline integrated circuit SOIC.

Write protection support for memory sectors using status register. In-system programming support with SRunner software driver. Additional programming support with the Altera?

System General, and other vendors. Software design support with the Altera Quartus? Delivered with the memory array erased all the bits set to 1. Whenever the term “serial configuration device s ” is used in. Serial configuration devices are flash memory devices with a. Cyclone series device and reload the data to the device upon power-up or. Serial Configuration Devices 3. Note to Table 4? This information is preliminary.

Similarly, you can vertically. FPGA and the configuration file size. Stratix II devices can only be used.

Raw Binary File Size. Notes to Table 4? These are preliminary, uncompressed file sizes. This is with the Stratix II compression feature enabled.

Configuration Handbook, Volume 2.

EPCS4N Datasheet, PDF – Alldatasheet

Cyclone II devices can be used with. This is with the Cyclone II compression feature enabled. Cyclone devices can only be used. This is with the Cyclone compression feature enabled. With the new data-decompression feature in the Stratix II and Cyclone. FPGA families, designers can use smaller serial configuration devices to. Serial configuration devices cannot be cascaded. The serial configuration devices are designed to configure Stratix II. Serial Configuration Device Block Diagram.

  HEF4528BP DATASHEET PDF

Accessing Memory in Serial Configuration Devices. You can access the unused memory locations of the serial configuration. Using this core, you can create a system with a Nios.

For more information on accessing memory within the serial. Serial AS configuration scheme.

EPCS1SI8N, EPCS4, EPCS4N

There are four signals on the serial configuration device that interface. The serial configuration device. Notes to Figures 4? For details, refer to the appropriate. The FPGA acts as the configuration master in the configuration flow and. Subsequently, the FPGA sends the. The serial configuration device responds to the instructions by. After initialization, the FPGA enters user.

Devices in the Configuration Handbook, Volume 1. Multiple devices can be configured by a single EPCS device. Stratix II or Cyclone device is the configuration master and has its. The following FPGAs are configuration. Multiple Devices in AS Mode.

Notes to Figure 4? This section describes the serial configuration device’s memory array. Timing specifications for the memory. Bytes bits per sector. Total number of pages. Serial Configuration Device Memory Access.

This section describes the operations that can be used to access the. The device samples the active eatasheet data input on the first rising edge of. Shift the operation code MSB first serially into the serial configuration. Each operation code bit is. Different operations require a different sequence of inputs.

For the datsheet byte, read status, and read silicon ID operations, the shifted. You can drive the nCS pin high after any bit of the data-out sequence is. For the write byte, erase bulk, erase sector, write enable, write disable. Otherwise, the operation is rejected and will not. All darasheet to access the memory contents while a write or erase cycle is.

  ANALYSIS TECHNIQUES FOR RACECAR DATA ACQUISITION JORGE SEGERS PDF

Operation Codes for Serial Configuration Devices. Write bytes operation requires at least one data byte on the DATA pin. If more than bytes are sent to the device.

The write enable operation code is b’and the most. The write enable operation sets the write. Always set the write. Write Enable Operation Timing Diagram. The write disable operation code is b’with the MSB listed.

The write disable operation resets the write enable latch bit, which. To prevent the memory from being written. Write bytes operation completion. Write status operation completion. Erase bulk operation completion.

Erase sector operation completion. Write Disable Operation Timing Diagram. The read status operation code is b’with the MSB listed first.

Dagasheet can use the read status operation to read the status register. Block Protect Bits [ Setting the write in progress bit to 1 indicates that the serial configuration.

Resetting the write in progress. Resetting the write enable latch bit to 0 indicates that no e;cs4n or erase. Set the write enable latch bit to 1 before every write. The non-volatile block protect bits determine the area of the memory.

The erase bulk operation is only. When any of the block. Sectors 6 and 7. The status register can be read at any time, even while a write or erase.

When one of these cycles is in progress, you can check. The device can also read the status register. Read Status Operation Timing Diagram. The write status operation code is b’with the MSB listed. Use the write status operation to set the status register block.