Have a look at the manual for your specific RP23 or download it from the fox website. The propedal settings for my RP23 are. I just got a Fox RP23 shock. Just follow directions on the Fox website. Your bikes manual should be able to tell you how much sag you. Here’s a quick overview of how to set up your Fox RP23 rear shock for best performance.
|Genre:||Health and Food|
|Published (Last):||17 July 2017|
|PDF File Size:||14.82 Mb|
|ePub File Size:||17.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
ProPedal damping reduces pedal-induced suspension bob. The proper rebound setting is a personal preference, and changes with rider weight, riding style and conditions. If this residual air sleeve lubricant is not present, this is an indication that the air sleeve should be re-lubricated. I fine the 1st pp setting does fine on ascents. You should notice the difference with Propedal on or off…. It should only be adjusted while in a stationary position.
The propedal settings for my RP23 are:. Because suspension designs and riding skills vary, optimal settings can vary from bike to bike and rider to rider.
fox float rpair pressure – Singletrack Magazine
Depending on riding style. Conversley with an RP23 on a Yeti ASR the nature of the design means you run a little lower psi than your weight in lbs.
All the above advice makes sense to me. Im 74kg with camelbak etc and use psi in Zesty RP If you can find your bikes manual on-line you should be able to get the intiial setup info in that, most people will then adjust this to suit their own riding manuual.
Take your shock pump with you on the next ride and add or subtract a bit until the bike rides how you want it to ride. I reckon not… Getting the right air pressure looks to be quite tricky too, I tried psi for my 85 kg, but after some posts here, I will probably end up a bit higher for a 9,5 mm sag….
Could anyone tell me from his own experience whether the settings are ok, or need mmanual be adapted for the Spark? It is a dream of a shock once bedded in. Then note pressure for future. Manufacturers have different tunes on the propedal to suit the bike. There may be a small amount of air sleeve lubricant residue on the body.
Have a look at the setup guide here: You are a little over that but alot depends on the suspension design and riding style. It should provide a stiffer ride but still provide full suspension action.
As above shock rated for upto psi, this may overwhelm the damping though rebound so may need a tune to keep it slow enough. Switch between positions and select the one that reduces suspension movement most effectively while providing the desired amount of bump absorption.
The three ProPedal knob settings are:. How you pedal is important too — you can learn not to bounce like a kid on a space hopper tloat. The ProPedal lever allows for on-the-fly ProPedal adjustment.
Usually a good starting point is your weight in lbs in psi. At just over kg I run circa lb on my Alpine.
No good — he has a DT shock. For faster reboundturn the red adjuster knob counterclockwise.
fox float rp23-air pressure
For slower reboundturn the red adjuster knob flowt. Some other things to consider for all shock models:. The Spark needs a medium tune at least.
I run psi rear and 75psi front F and am 13st 9lb. You can also view a Flash video on Setting Sag.
You could try stripping and rebuilding without a new seal. Thanks Posted 6 years ago. I managed to set up the air pressure correctly, but what really surprised me was the side play…will have to use some 0,5 mm spacers for each side….
The two ProPedal lever settings are:. If the pro pedal makes the shock locked out your using too much air. A rule of thumb is that rebound should be manula fast as possible without kicking back and pushing the rider off the saddle.
You do need rp233 high amount of PSI for the Spark to pedal properly — what compress tune rp32 the shock have? With an RP23 on an Orange 5 the nature of the design means you run a little higher psi than your weight in lbs. I reckon not… Getting the right air pressure looks to be quite tricky too, I tried psi for my 85 kg, but after some posts here, I will probably end up a bit higher for a 9,5 mm sag… Posted 6 rrp23 ago.
Did that on mine when I got it and its been fine till a tf service a year later. Viewing 32 posts – 1 through 32 of 32 total. Have a look at the setup guide here:.