LM311N DATASHEET PDF

LMN Datasheet, LMN National Semiconductor Voltage Comparator Datasheet, buy LMN. The LM, LM, LM are voltage comparators that have low input currents. They are also designed to operate over a wide range of. Part, LMN. Category. Description, Voltage Comparators. Company, ST Microelectronics, Inc. Datasheet, Download LMN datasheet. Cross ref.

Author: Dashicage JoJotilar
Country: Czech Republic
Language: English (Spanish)
Genre: Career
Published (Last): 15 December 2006
Pages: 177
PDF File Size: 1.52 Mb
ePub File Size: 1.27 Mb
ISBN: 123-6-85560-785-9
Downloads: 69903
Price: Free* [*Free Regsitration Required]
Uploader: Zolosida

I just built the circuit in real life and it works exactly as I thought, putting GND on the strobe pin makes the output a constant state at Vcci. As grounding unused pins is a practice on electronics, I guess it was the way of the designer to make sure the device was not disabled for a ground wired to that pin.

You can note that the Output voltage stays high when pin 2 has higher voltage than pin 7 and vice versa.

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Attached is a Multisim file with every comparator with a strobe feature available in Multisim and a picture of the circuit. LMN Comparator with Strobe.

LMN STMicroelectronics | Ciiva

A sample circuit is shown below in which the Inverting Terminal is set to 2. The LM can work on a Single supply voltage or in a dual supply mode.

  HODGE WARFIELD INSPIRATION PDF

An Emitter Output Circuit is shown below. Message 1 of 5. TL — Programmable Reference Voltage. Submitted by admin on 6 March Message 5 of 5.

Why is it not working in Multisim? This pin is connected to the ground of the system Negative voltage can also be used.

Most Active Software Boards: The transistor can also make the Load to be isolated from the system ground, so if you are looking for a Voltage comparator to drive loads of these specifications then this IC might be the right choice for you.

Normally these pins are not used since the Input Offset itself is much better controlled.

Multisim and Ultiboard

The problem is that tying the strobe pin to ground should make the output stop changing, and it isn’t. The pins 5 and 6 on the Op-amp are used to set the balance voltage if you want to manually adjust the DC-Offset voltage.

The problem is that the strobe pin is not working for the model. Any Op-Amp can be made to work as a voltage comparator, but the LM proves itself to be advantages by housing an Output Transistor inside its package. Any help is appreciated. Could the component model be the issue?

  JEAN-DOMINIQUE BAUBY LE SCAPHANDRE ET LE PAPILLON PDF

The simplified schematics of the IC is shown below: When not in use the pins 5 and 6 should be shorted as shown above. Message 2 of 5. Message 4 of 5. The simplified schematics of the IC is shown below:. All of those comparator outputs should be a high state which means the LED will turn on connected through the 1K resistor to Vcc. The output is correct as seen on the scope.

I tried adding in a transistor with a 1k resistor to ground and a TTL signal at the base as per the datasheet and this doesn’t disable the output either. Message 3 of 5. If the voltage at the Non-Inverting Terminal pin 2 is higher than the Inverting Terminal pin 2the output pin 7 will also be high else the output will be low.

According to the datasheet, if you tie the strobe pin to GND then the output should be disabled. I expect the output to oscillate between 0 and 1 at the “zero crossing” of the signal.

I built a simple circuit using the LMN comparator. You can refer the other possible circuits from the LM datasheet given at bottom.